NEC Express5800/120Rh-2 User Manual Download Page 398

Page: 398 / 406

F-12 Installing Windows 2000

Re-install the Network Driver

After installing OS and deleting the network drivers, if you want to re-install the network drivers,
follow the procedure below.

Restart OS and logon to your system.

[Upgrade Device Driver Wizard] dialog box appears.

Click [Next].

Confirm that the [Search for a suitable driver for my device (recommended)] radio button
is selected and click [Next].

Select the [Specify a location] check box and deselect other check boxes.

Click [Next].

Other [Upgrade Device Driver Wizard] dialog box opens.

When using [Intel(R) PRO/1000MT Dual Port Network Connection], specify [<CD-ROM
drive letter>:\WINNT\W2K\BC5\PRO1000\WIN2K].

Then click [OK].

Click [Next].

Click [Finished].

After re-installing the network drivers, the link speed and Duplex mode need to be
specified.

Refer to "Network Driver" described earlier.

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Search results

Summary of Contents for Express5800/120Rh-2

Reviews:

NEC Express5800/120Rh-2, User Manual, Page: 398 / 406

Search results

Summary of Contents for Express5800/120Rh-2

Reviews: