NEC Express5800/120Rh-2 Page 144 User Manual Download

Page: 144 / 406

5-2 Installing the Operating System with Express Setup

About Express Setup

"Express Setup" helps you to install the Windows Operating System.

The setup automatically configures the RAID system and installs the Operating System and some
management software.

IMPORTANT:

Executing the Express Setup erases all data on the

hard disk drive.

You can also use "Configuration disk" at "Express Setup" in order to save or backup parameters for
installation.

The Configuration disk is able to have some parameters files that include the configuration
information for the server setup.

If you want to set up the server as before, execute the Express Setup with the parameters file you
have saved before.

NOTES:

The parameters file is not mandatory to set up the system.

If you want to create a parameters file, have a blank floppy
disk(MS-DOS 1.44MB format) ready.

If you want to use the drivers located on the "OEM-Disk for Mass
Storage Device" that ships with optional boards, a parameters file
is mandatory.

You can create a parameters file in advance using "Configuration
Diskette Creator" included in NEC EXPRESSBUILDER.

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Search results

Summary of Contents for Express5800/120Rh-2

Reviews:

Related manuals for Express5800/120Rh-2

Brands by name

Popular brands

NEC Express5800/120Rh-2, User Manual

Search results

Summary of Contents for Express5800/120Rh-2

Reviews:

Related manuals for Express5800/120Rh-2

Brands by name

Popular brands