NEC Express5800/120Rh-2 Page 379 User Manual Download | Manualshive

Page: 379 / 406

background image

Installing Windows Server 2003 E-17

NOTE:

We recommend you to add [Network Monitor] at [Adding

Services]. [Network Monitor] can monitor the frame (or the packet) that
the computer installing [Network Monitor] sends or receives. This tool
is valuable when analyzing network trouble. For information on how to
install the tool, see the "Setting for Solving Problems" in Chapter 5.

Re-install the Network Driver

The network driver will be installed automatically.

Graphics Accelerator Driver

Standard graphics accelerator drivers that are mounted will be installed automatically.

The following is the procedure when it is necessary to install manually.

If you want to utilize optional Graphics Accelerator Driver board, follow the document attached to
the board to install the driver.

* For the graphics accelerator driver, the use of a remote KVM console that installs the advanced

N8115-02 remote management card is supported by the standard.

1.

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

2.

Click Start menu, point to [Programs], [Accessories] and click [Windows Explorer]

3.

Run "SETUP.EXE" in the following directory.

<CD-ROM Drive Letter>:\WINNT\DOTNET\VIDEO\SETUP.EXE

4.

Follow the message to continue the installation.

5.

Remove the NEC EXPRESSBUILDER CD-ROM from the CD-ROM drive, follow the
direction on the screen and restart the system.

«
...
377
378
379
380
381
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Brand: IBM Pages: 151

Brand: 360 Systems Pages: 8

Brand: Xerox Pages: 24

DocuColor 7000AP

Brand: Xerox Pages: 36

Brand: IBM Pages: 74

Brand: Axis Pages: 66

Brand: 3onedata Pages: 3

AND-APL1E Series

Brand: Acrosser Technology Pages: 42

ConnectPort LTS 16

Brand: Digi Pages: 169

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 8

Brand: Toshiba Pages: 12

Brand: Toshiba Pages: 8

Brand: Toshiba Pages: 16

IPedge EP Server

Brand: Toshiba Pages: 19

SD-H400 - Combination Progressive-Scan DVD Player

Brand: Toshiba Pages: 53

Brand: Toshiba Pages: 185

Digital Media Server

Brand: Toshiba Pages: 204

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands