NEC Express5800/120Rh-2 Page 212 User Manual Download | Manualshive

Page: 212 / 406

background image

6-14 Installing and Using Utilities

CONFIGURATION DISKETTE CREATOR

"Configuration Diskette Creator" is a tool to create [Configuration Diskette] that is used for
configuring the server with the Express Setup (see Chapter 5 for details).

If you use the Configuration Diskette created by the Express Setup and Configuration Diskette
Creator to operate the setup, you can setup from the installation of OS to several utilities
automatically except for a few key input to confirm the specification. Also, you can install the
system with the same specification as before when re-installing the system. We recommend you to
create [Configuration Diskette] to setup the servers from NEC EXPRESSBUILDER.

IMPORTANT:

You can not create [Configuration Diskette] for

Microsoft Windows Server 2003 x64 Editions.

NOTE:

You can install Windows Server 2003 and Windows 2000

without [Configuration Diskette]. Also, you can modify/newly create
[Configuration Diskette] during the setup with NEC
EXPRESSBUILDER.

Creating Configuration Diskette

This section describes about specifying setup information that is necessary for OS installation and
creating [Configuration Diskette]. Follow the procedure below.

NOTE:

In the procedure below, the folder name that is specified when

installing Trekking command is assumed as [Configuration Diskette
Creator].

1.

Start the OS.

2.

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

Master Control Menu will appear.

3.

Right-click on the screen or left-click [Setup]. The menu will appear.

«
...
210
211
212
213
214
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Express5800/180Ra-7

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rg-1

Brand: NEC Pages: 2

Express5800/120Rf-1

Brand: NEC Pages: 21

Express5800/120Ra-1

Brand: NEC Pages: 6

Express5800/120Mc2 series

Brand: NEC Pages: 2

EXPRESS5800/120Le

Brand: NEC Pages: 56

Express5800 320La

Brand: NEC Pages: 8

Express5800 120Li

Brand: NEC Pages: 2

Express5800 120Ed

Brand: NEC Pages: 29

Active Upgrade Express5800/320Fc

Brand: NEC Pages: 4

Brand: NEC Pages: 10

Express5800/120Rj-2

Brand: NEC Pages: 18

Express5800/120Rh-1

Brand: NEC Pages: 20

Bull NovaScale R620 Series

Brand: NEC Pages: 346

Express5800 320La

Brand: NEC Pages: 206

Express5800/R110j-1

Brand: NEC Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands