NEC Express5800/120Rh-2 Page 108 User Manual Download

Page: 108 / 406

4-12 Configuring Your Server

Advanced Chipset Control

Option

Parameter

Description

Your Setting

Enable Multimedia
Timer

[No]
Yes

Specify whether the system supports
the multimedia timer feature.

Wake On
LAN/PME

Disabled
[Enabled]

Specify whether the remote power-on
function through embedded NIC, PCI
devices in slots 1 to 5 is enabled or
disabled.

Wake On Ring

[Disabled]
Enabled

Specify whether the remote power-on
function through a serial port is
enabled or disabled.

Wake On RTC
Alarm

[Disabled]
Enabled

Specify whether the remote power-on
function by using RTC alarm feature is
enabled or disabled.

[ ]: Factory-set

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Search results

Summary of Contents for Express5800/120Rh-2

Reviews:

Related manuals for Express5800/120Rh-2

Brands by name

Popular brands

NEC Express5800/120Rh-2, User Manual

Search results

Summary of Contents for Express5800/120Rh-2

Reviews:

Related manuals for Express5800/120Rh-2

Brands by name

Popular brands