NEC Express5800/120Rh-2 Page 288 User Manual Download | Manualshive

Page: 288 / 406

background image

9-14 Upgrading Your Server

5.

Grasp the handle and firmly push the power supply.

The power supply unit is locked when a distinct "click" is heard.

6.

Connect two power cords.

Use the power cord provided with the standard power supply unit and the one provided
with the system. The AC POWER LEDs flash when the power cords are connected.

7.

Power on the server.

The AC POWER LEDs go on.

8.

Confirm, by the STATUS LED or on the POST screen, that there are no errors related to
the power supply units.

See Chapter 8 for details on the error messages.

If the AC POWER LEDs are off, reinstall the power supply units. If the same error
message still appears, contact your service representative.

Power cord for
power supply unit 1

Power supply unit 1

(Standard)

Power supply unit 2

(Option)

Power cord for
power supply unit 2

AC POWER LEDs

«
...
286
287
288
289
290
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

SuperServer E100-8Q

Brand: Supermicro Pages: 48

NECCare Platinum Express5800/A1160

Brand: NEC Pages: 4

NECCare Gold Express5800/320Fd

Brand: NEC Pages: 11

NEC Express5800/R120d-2E

Brand: NEC Pages: 39

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 244

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 191

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 96

Brand: Lanner Pages: 43

Brand: Omega Pages: 49

Brand: Iwatsu Pages: 338

301300U - Ethernet Disk NAS Server

Brand: LaCie Pages: 62

xPort Pro XPP1004000-02R

Brand: Lantronix Pages: 17

Brand: Autonomic Pages: 17

Brand: NetMedia Pages: 2

Enterprise Server 33

Brand: Blackberry Pages: 207

SUPERSERVER 5025M-UR

Brand: Supermicro Pages: 130

Brand: Xblue Networks Pages: 2

Brand: Arris Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands