NEC Express5800/120Rh-2 Page 372 User Manual Download | Manualshive

Page: 372 / 406

background image

E-10 Installing Windows Server 2003

7.

When the following message is displayed, press

S

.

Setup could not determine the type of one or more mass storage devices
installed in your system, or you have chosen to manually specify an adapter.
Currently, Setup will load support for the following mass storage devices.

The following message is displayed.

Please insert the disk labeled

manufacturer-supplied hardware support disk

into Drive A:

*Press ENTER when ready.

8.

Insert the Windows Server 2003 OEM-DISK for NEC EXPRESSBUILDER into the
floppy disk drive, and press

Enter

.

A list of mass storage devices is displayed.

Select the [Adaptec Ultra320 SCSI Cards (Win XP/Server 2003 IA-32)] and press

Enter

.

Then, it returns to the screen of Procedure 7.

9.

If the optional board is installed, select the proper SCSI Adapter and press

Enter

.

–

Adaptec HostRAID U320 Driver Ver 1.02 For Windows 2000/XP/2003
(When Adaptec HostRAID (SCSI) is installed.)

–

MegaRAID SCSI 320-1 RAID Controller Driver
(When N8103-80F board is installed.)

–

MegaRAID SCSI 320-2 RAID Controller Driver
(When N8103-81F board is installed.)

–

Adaptec I2O RAID Driver Disk for 32bit Windows 2000/XP/2003
(When N8103-86 board is installed.)

–

LSI Logic MegaRAID SAS RAID Controller Driver (Server 2003 32-bit)
(When N8103-91F board is installed.)

Continue performing tasks according to the subsequent messages that appear.

10.

When the following message is shown, press

Enter

to start "Welcome to Setup".

11.

When the installation of Windows Server 2003 has finished, the system reboots
automatically.

–

Windows Server 2003 has been installed: Go on the step 15.

–

Windows Server 2003 R2 has been installed: Go on the step 12.

«
...
370
371
372
373
374
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Brand: KYLAND Pages: 30

Brand: Jung Pages: 16

88743BU - System x3950 E

Brand: IBM Pages: 426

Brand: Artesyn Pages: 190

Brand: Hamlet Pages: 76

Brand: ARAID Pages: 20

Brand: Supermicro Pages: 96

Brand: Supermicro Pages: 130

Brand: Supermicro Pages: 124

Brand: Biamp Pages: 11

Brand: Planet Pages: 93

Brand: Lindy Pages: 2

Brand: NexPath Pages: 166

Brand: Cooper Bussmann Pages: 94

Brand: W&T Pages: 79

Brand: Intel Pages: 30

Brand: Intel Pages: 270

Brand: Qbox Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands