manualshive.com logo in svg

NEC Express5800/120Rh-2, User Manual, Page: 313 / 406

Share
Download
NEC Express5800/120Rh-2 User Manual Download Page 313

Upgrading Your Server  9-39

Use of internal hard disk drives in a disk array configuration

To use the internal hard disk drives in a disk array configuration in the server containing a disk array
controller board, reconnect the SCSI cables and LED cables on the mother board.
The internal hard disk drive interface is connected to the SCSI connector on the mother board at
shipment.

IMPORTANT:

 When using N8103-91 disk array controller, you do

not need to connect an LED cable.

Standard configuration

Mother board

REAR

FRONT

Hard disk

drive

SCSI ID3-5

Internal backup

device

Hard disk

drive

SCSI ID0-2

SCSI backplane

SCSI connector

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments