NEC Express5800/120Rh-2 Page 156 User Manual Download | Manualshive

Page: 156 / 406

background image

5-14 Installing the Operating System with Express Setup

Installing and Setting Device Drivers

Follow these steps to install and configure the device drivers.

PROSet

PROSet is a utility that confirms the function of network contained in network driver.

Utilizing PROSet enables the following items:

Confirm detailed information of the adapter.

Diagnose loop back test, packet transmission test and so on.

Setup of teaming.

Configuring several network adapters as one team provides the server a tolerant environment on any
trouble and enhance throughput between the switches.

PROSet is necessary to utilize these features.

Follow the procedure below to install PROSet.

1.

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

2.

The [Windows Explorer] dialog starts.

* The procedure in the case of the standard start menu

Click Start menu and click [Windows Explorer].

* The procedure in the case of the classic start menu

Click Start menu, point to [Programs], [Accessories] and click [Windows Explorer].

3.

Run "PROSET.EXE" in the following directory.

<CD-ROM DriveLetter>:\WINNT\DOTNET\BC5\PROSET\WS03XP32

The [Intel(R) PROSet - InstallShield Wizard] dialog starts.

4.

Click [Next].

5.

Choose "I accept the terms in the license agreement" and click [Next].

6.

Choose "Typical" and click [Next].

7.

Click [Install].

8.

When [InstallShield Wizard Completed] window is displayed, click [Finish].

9.

Restart the system.

«
...
154
155
156
157
158
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

SUPERSERVER 6035B-8R+

Brand: Supero Pages: 110

Brand: Data-Tronix Pages: 29

Brand: Data-Tronix Pages: 30

RIP Station 5100

Brand: Epson Pages: 140

PRIMERGY TX2550 M4

Brand: Fujitsu Pages: 563

IP-DECT SERVER 6500

Brand: SpectraLink Pages: 2

WSG SoundGrid Server One

Brand: Waves Pages: 4

Brand: IBM Pages: 16

Brand: ELStorage Pages: 3

Brand: Bosanova Pages: 2

Brand: Bosanova Pages: 2

Brand: Supermicro Pages: 78

SuperWorkstation 5049A-TR

Brand: Supermicro Pages: 189

SuperStorageServer SSG-6119P-ACR12N4L

Brand: Supermicro Pages: 211

LASERSHARE PS-MIO

Brand: BayTech Pages: 133

Brand: ICP DAS USA Pages: 8

Brand: 7th Sense Pages: 24

easyRAID FN-420GT

Brand: easyRAID NAS Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands