NEC Express5800/120Rh-2 Page 175 User Manual Download | Manualshive

Page: 175 / 406

background image

Installing the Operating System with Express Setup 5-33

Windows 2000

Express Setup can install Windows 2000 operating system. Confirm below notes before installing
the Windows.

IMPORTANT:

Before starting the installation, complete all the process of adding
the optional device and the setup of Express server mainframe
(BIOS and optional board specification)

The document for installing Windows 2000 is also attached to the
other software package which is sold separately from NEC, but
refer to this document when you install Windows 2000 on this
model.

After completing Express Setup, see "Setup for Solving Problems"
described later to specify the settings for trouble recovery such as
"Specifying Memory Dump".

Installing on the Mirrored Volume

If you want to install Windows 2000 on the volume that is mirrored using "Disk Management",
invalid the mirroring before operating the installation to set back to the basic disk, and valid the
mirroring again after the installation has completed.

Creating, invalid, delete mirror volume can be operated from "Disk Management" in "Computer
Management".

Connecting MO Device

If you operate installing Windows 2000 with MO device connected, the installation may not be
completed normally. In such case, detach MO device and then re-install the system from the
beginning.

Media such as DAT

During the OS installation, do not attach the unnecessary media for OS installation to the system,
such as DAT.

Connecting Hard Disk Drive

Connect the hard disk drive that OS is not going to be installed after installing OS.

If you create multiple logical drives in your system, refer to "Re-installing the operation system
when multiple logical drives exist" (Appendix E).

«
...
173
174
175
176
177
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Brand: KYLAND Pages: 30

SBXL52 - Server Compute Blade

Brand: Intel Pages: 126

eServer BladeCenter HS40 Type 8839

Brand: IBM Pages: 120

9123710 - eServer OpenPower 710

Brand: IBM Pages: 70

INTUITY AUDIX LX

Brand: Avaya Pages: 68

Brand: Supermicro Pages: 124

Brand: Huawei Pages: 39

Brand: Huawei Pages: 188

5288 V3 V100R003

Brand: Huawei Pages: 297

Brand: Huawei Pages: 2

Brand: Wyse Pages: 2

PS121v2 - USB Mini Print Server

Brand: NETGEAR Pages: 50

Brand: NETGEAR Pages: 124

Digital Entertainer HD EVA8000

Brand: NETGEAR Pages: 114

Brand: Grafenthal Pages: 99

LANTIME M600 MRS

Brand: Meinberg Pages: 160

Brand: Supermicro Pages: 82

Brand: Obvius Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands