National Instruments Corporation GPIB-1014P User Manual Download Page 54 | Manualshive

Page: 54 / 171

background image

Section Four

Register Bit Descriptions

© National Instruments Corporation

4-17

GPIB-1014P User Manual

Bit

Mnemonic

Description

pon:

power on reset

Read ISR2:

Bit is cleared immediately after it is read.

The SRQI bit indicates that a GPIB Service Request (SRQ) message has
been received while the TLC Controller function is active (CIC=1).

5r

LOK

Lockout Bit

LOK is used, along with the REM bit, to indicate the status of the TLC
GPIB Remote/Local (RL) function. If set, the LOK bit indicates that the
TLC is in Local With Lockout State (LWLS) or Remote With Lockout
State (RWLS). LOK is a non-interrupt bit.

5w

DMAO

DMA Out Enable Bit

The DMA feature is not implemented. Do not set this bit.

4r

REM

Remote Bit

This bit is true whenever the TLC GPIB RL function is in one of two
states: Remote State (REMS) or Remote With Lockout State (RWLS).
The TLC RL function enters one of these states when the System
Controller has asserted the Remote Enable line (REN), and the
Controller-In-Charge addresses the TLC as a Listener.

4w

DMAI

DMA Input Enable Bit

The DMA feature is not implemented. Do not set this bit.

3r

CO

Command Out Bit

3w

CO IE

Command Out Interrupt Enable Bit

CO is set when:

(CACS & SGNS) becomes true

CO is cleared by:

(Read ISR2) + -(CACS) + -(SGNS)

Notes:

CACS:GPIB Controller Active State
SGNS:GPIB Source Generate State
Read ISR2:

Bit is cleared immediately after it is read.

CO = 1 indicates CDOR is empty and that another command can be
written to it for transmission to the GPIB without overwriting a previous
command.

«
...
52
53
54
55
56
...
»

Summary of Contents for GPIB-1014P












































































































































































Reviews:

No comments

Related manuals for GPIB-1014P

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

Brand: GE Pages: 802

Brand: iET Pages: 17

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: NEILPRYDE Pages: 53

Brand: 3Disc Pages: 12

Brand: QBC Diagnostics Pages: 65

Brand: IDEAL Networks Pages: 10

Brand: PacBio Pages: 13

Brand: Pablo Pages: 4

Brand: PA Pages: 28

Brand: York Pages: 26

Brand: Pari Pages: 11

Brand: Pari Pages: 2

Brand: Haas Pages: 5

QNET Physics and Dynamics

Brand: Quanser Pages: 4

Brand: A.HABERKORN Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands