Rockhopper II series printers – User’s Guide
15
AP-75095, Rev. 2.0, 24/10/03
¾
When cutting the roll media, be careful of the following. Incorrect handling can result in injury to the
hands and fingers from the razor blade.
o
When holding the media, do not place fingers over the media cut groove.
o
Move the razor blade slowly along the media cutting groove.
¾
Do not use thinner, benzene, alcohol or other active agents. Doing so may result in damage or paint
peeling from the casing.
¾
Be careful not to spill water inside the printer. Doing so may result in a short circuit.
¾
Be careful not to touch the heaters during or after operation. Doing so may result in burns.
¾
Only use Eco-Solvent ink, Eco-Solvent Plus ink and appropriate cleaning liquid. Using other ink (e.g.
dye or pigment) will cause permanent damage to the printer.
¾
Do not use Eco-Solvent ink in combination with Eco-Solvent Plus™ ink. Doing so will cause
permanent damage to the printer.
¾
Never open the covers fixed with screws. Doing so may result in electrical shock or a malfunctioning
in the printer.
¾
Do not touch the cutter blade. Doing so may result in bodily injury.
¾
Do not cut hard objects or drop the cutter. Doing so may damage or chip the cutter blade.
¾
Do not bend or pull the waste fluid tube. Doing so may cause that the waste fluid will leak out and
malfunction in the product.
¾
Do not touch the cleaning wiper or the head cap unit while cleaning the cleaning wiper. Doing so may
result in poor head cleaning because of oil on your hands.
¾
Do not tilt the printer, stand it against a wall or turn it upside down. Doing so may cause ink to leak
inside the printer. Movement after transport is also not covered by the warranty.
¾
When installing options, do not touch the elements on the circuit board. The elements on the boards
can be very hot and can cause burns.
¾
Have four or more people unpack and assemble the printer.
¾
When lifting the printer out of the packing box, be sure to remove the vinyl cover first, then grab the
holding grips on the sides of the printer. Lifting the printer with the vinyl cover on may cause your
hands to slip and drop or damage the printer.
¾
Have two or more people transport the printer.
¾
Ensure that the plug has been disconnected from the power socket when it is not to be used for a long
time.
¾
Earth wires must be connected to wires or terminals that fulfill the conditions below.
o
Earth terminals of power sockets
o
Earth wires with copper morsel that is at least 650 mm under the ground
¾
Earth wires must be connected to wires or terminals that fulfill the conditions below.
Summary of Contents for Rockhopper II Series
