Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download

Page: 16 / 94

Web Console Configuration

In this chapter, we explain all aspects of web-based console configuration. Moxa’s easy-to-use management
functions help you set up your AWK-3131A-M12-RCC and make it easy to establish and maintain your wireless
network.

The following topics are covered in this chapter:



Web Browser Configuration













Wireless Settings



Operation Mode



Basic Wireless Settings



WLAN Security Settings



Advanced Wireless Settings



WLAN Certification Settings (For EAP-TLS in Client/Slave Mode Only)



Extended Control Settings (AP Mode Only)



Advanced Settings



Using Virtual LAN



Configuring Virtual LAN



DHCP Server (For AP Mode Only)



Packet Filters



RSTP Settings (for AP/Master/ACC mode only)



SNMP Agent



Link Fault Pass-Through (for Client/Slave mode only)



Auto Warning Settings

















Associated Client List (For AP/Master/ACC Mode Only)



AP Throughput



DHCP Client List (For AP Mode Only)



System Log



Relay Status

Summary of Contents for Airworks AWK-3131A-M12-RCC






























































































Search results

Summary of Contents for Airworks AWK-3131A-M12-RCC

Reviews:

Related manuals for Airworks AWK-3131A-M12-RCC

Brands by name

Popular brands

Moxa Technologies Airworks AWK-3131A-M12-RCC, User Manual

Search results

Summary of Contents for Airworks AWK-3131A-M12-RCC

Reviews:

Related manuals for Airworks AWK-3131A-M12-RCC

Brands by name

Popular brands