Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download | Manualshive

Page: 46 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-31

Policy

Setting

Description

Factory Default

Accept

Only the packets fitting the entities on list can be allowed.

Accept

Drop

Any packet fitting the entities on list will be denied.

RSTP Settings (for AP/Master/ACC mode only)

AWK-3131A-M12-RCC supports IEEE802.1D Spanning Tree Protocol and IEEE802.1w Rapid STP standards. In
addition to eliminating unexpected path looping, STP/RSTP can provide a backup path recovery if a wired/
wireless path fails accidentally. The reliability and availability can increase because this fail-over function.

AWK-3131A-M12-RCC’s STP/RSTP feature is disabled by default. To be completely effective, you must enable
RSTP/STP on every AWK-3131A-M12-RCC connected to your network. If AWK-3131A-M12-RCC plays a Client
role, which is connected to a device (PLC, RTU, etc.) as opposed to network switch equipment, it is not
necessary to enable STP/RSTP. The reason is that it will cause unnecessary negotiation.
AWK-3131A-M12-RCCs support STP/RSTP in AP mode only.

The following figures indicate which Spanning Tree Protocol parameters can be configured. A more detailed
explanation of each parameter is given below the figure.

RSTP status

This field will appear only when selected to operate STP/RSTP. It indicates whether this AWK-3131A-M12-RCC
is the Root of the Spanning Tree (the root is determined automatically) or not.

Bridge priority

Setting

Description

Factory Default

Numerical value
selected
by user

You can increase the bridge priority by selecting a lower
number. A higher bridge priority brings a greater chance of
being established as the root of the Spanning Tree topology.

32768

Hello time

Setting

Description

Factory Default

Numerical value input
by user
(1 – 10 seconds)

The root of the Spanning Tree topology periodically sends out a
“hello” message to other devices on the network to check if the
topology is healthy. Hello time indicates how often the root
sends hello messages.

2 (seconds)

ATTENTION

Be careful when you enable the filter function:
Drop + “

no

entity on list is activated” = all packets are allowed

Accept + “

no

entity on list is activated” = all packets are denied

«
...
44
45
46
47
48
...
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

Brand: IBM Pages: 104

System Storage TS3100

Brand: IBM Pages: 375

Brand: Dahua Pages: 6

NetStructure ZT 5515

Brand: Intel Pages: 90

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Brand: ZyXEL Communications Pages: 282

Parallel Printer Card PIOC

Brand: B&B Electronics Pages: 16

Brand: Davey Pages: 18

Brand: T.A Pages: 11

Brand: peplink Pages: 2

IMACS Network Device

Brand: Zhone Pages: 114

Brand: M86 Security Pages: 309

NetCon FBR-1409TX

Brand: LevelOne Pages: 88

Brand: Teldat Pages: 23

Brand: Ubiquiti Pages: 20

DotSurfer GPC-2100

Brand: Gtran Wireless Pages: 44

IntraSwitch 5324MT

Brand: Asante Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands