Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download | Manualshive

Page: 53 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-38

E-mail

E-mail Event Types

Check the box for Active to enable the event items. All default values are deactivated (unchecked). Details for
each event item can be found on the “System log Event Types” table on page 3-31.

E-mail Server Settings

You can set up to 4 e-mail addresses to receive alarm emails from the AWK-3131A-M12-RCC. The following
parameters can be configured on the E-mail Server Settings page. In addition, a Send Test Mail button can
be used to test whether the Mail server and e-mail addresses work well. More detailed explanations about these
parameters are given after the following figure.

Mail server (SMTP)

Setting

Description

Factory Default

IP address

The IP Address of your email server.

None

User name & Password

Setting

Description

Factory Default

User name and password used in the SMTP server

None

«
...
51
52
53
54
55
...
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

Brand: D-Link Pages: 28

Brand: D-Link Pages: 2

DIR-655 - Xtreme N Gigabit Router Wireless

Brand: D-Link Pages: 3

Brand: D-Link Pages: 11

Brand: D-Link Pages: 12

Brand: D-Link Pages: 12

Brand: D-Link Pages: 24

Brand: D-Link Pages: 20

Brand: D-Link Pages: 44

Brand: D-Link Pages: 52

Brand: D-Link Pages: 103

Brand: Garland Pages: 6

Brand: Hawking Pages: 2

Brand: Alcad Pages: 6

Brand: Acqiris Pages: 22

Brand: FOR-A Pages: 2

Brand: Axis Pages: 104

Brand: Intel Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands