Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download Page 37 | Manualshive

Page: 37 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-22

Beacon Interval (for AP/Master/ACC mode only)

Setting

Description

Factory Default

Beacon Interval
(40 to 1000 ms)

Indicates the frequency interval of the beacon

100 (ms)

DTIM Interval (for AP/Master/ACC mode only)

Setting

Description

Factory Default

Data Beacon Rate
(1 to 15)

Indicates how often the AWK-3131A-M12-RCC sends out a
Delivery Traffic Indication Message

1

Fragmentation threshold

Setting

Description

Factory Default

Fragment Length
(256 to 2346)

Specifies the maximum size a data packet before splitting and
creating another new packet

2346

RTS threshold

Setting

Description

Factory Default

RTS/CTS Threshold
(256 to 2346)

Determines how large a packet can be before the Access Point
coordinates transmission and reception to ensure efficient
communication

2346

NOTE

Most countries define a limit for the Equivalent Isotropically Radiated Power (EIRP) for an RF transmitting
system. The EIRP should not exceed the permitted limit for the country of operation. EIRP = transmission
power + antenna gain (dBi).

NOTE

Transmission power indicates the maximum value of transmission power which the user plans. However, the
real transmitted power depends on the radio module and some facts, such as country, regulatory limitations
and data rate. Please check the Transmission power in Status > Wireless Status for a real and updated value
of transmission power, which the AWK is currently using.

You can refer to the related glossaries in the reference section for detailed information about the
above-mentioned settings. By setting these parameters properly, you can better tune the performance of your
wireless network.

Antenna

Setting

Description

Factory Default

A/B/Both

Specifies the output antenna port. Setting Antenna to Both
allows 2x2 MIMO communication under 802.11n and 2T2R
communication in legacy 802.11a/b/g modes.

Both

WMM

Setting

Description

Factory Default

Enable/Disable

WMM is a QoS standard for WLAN traffic. Voice and video data
will be given priority bandwidth when enabled with WMM
supported wireless clients.

Disable

ACC Connection Threshold

Setting

Description

Factory Default

ACC Connection
Threshold

If the signal strength of an AWK-3131A-M12-RCC can be above
this value for the period of time specified in the “ACC
Connection Time” field, this AWK-3131A-M12-RCC will be
considered as a connecting candidate.

-60dBm

«
...
35
36
37
38
39
...
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

Brand: Acconeer Pages: 32

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: Datasheen Pages: 25

Brand: Enginko Pages: 19

Brand: Patton electronics Pages: 12

EdgeLens INT10G8LR56

Brand: Garland Pages: 30

Brand: Tripp Lite Pages: 3

Brand: Abocom Pages: 2

GSM7224v2 - Layer 2 Managed Gigabit Switch

Brand: NETGEAR Pages: 3

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: Aurora Pages: 6

Brand: S&T Pages: 28

Brand: Unex Pages: 27

Brand: ekwb Pages: 11

TeleMyo 2400T V2

Brand: Noraxon Pages: 52

IE-SW-VL09T-6TX-3SC

Brand: Weidmuller Pages: 14

RoteFinder RF500S

Brand: Multi-Tech Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands