Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download Page 14 | Manualshive

Page: 14 / 94

background image

AWK-3131A-M12-RCC

Getting Started

4-2

How to Test Two or More AWK-3131A-M12-RCC Units

If you have two or more AWK-3131A-M12-RCC units, you will need a second notebook computer (Notebook B)
equipped with an Ethernet port. Use the default settings for the first AWK-3131A-M12-RCC connected to
notebook A and change the second or third AWK-3131A-M12-RCC connected to notebook B to Client mode, and
then configure the notebooks and AWK-3131A-M12-RCC units properly.

After setting up the testing environment, open the Windows Command Prompt on notebook B. At the prompt,
type:

ping <IP address of notebook A>

and then press Enter. A “Reply from IP address …” response means the communication was successful. A
“Request timed out” response means the communication failed. In this case, recheck the configuration to make
sure the connections are correct.

«
...
12
13
14
15
16
...
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

Brand: Paradyne Pages: 2

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: Zhone Pages: 2

Brand: Accusys Pages: 34

Brand: Medel Pages: 28

Brand: Idis Pages: 22

Brand: Federal Signal Corporation Pages: 49

Brand: Supermicro Pages: 15

Brand: Acromag Pages: 23

Brand: Top Pages: 21

Brand: Alcatel-Lucent Pages: 60

Brand: V-Count Pages: 2

DataFire GO! PRO

Brand: Digi Pages: 20

AdvancedTCA AT8901M

Brand: Kontron Pages: 76

Brand: Aaeon Pages: 119

Brand: Multi-Link Pages: 31

Brand: MicroNova Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands