Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download | Manualshive

Page: 28 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-13

Netmask

Setting

Description

Factory Default

Netmask for client
isolation function

This setting can be used when the Isolated within the same
subnet option is selected.
If the Subnet Type is set to Static, this setting must be
applied. If the Subnet Type is set to DHCP, this field can be left
blank and the gateway address will be assigned by the DHCP
server.

None

The Allowed subnet with TCP/UDP port setting is used to specify the exceptions (subnets or hosts) when
the Isolated within the same subnet option is selected. Up to eight subnets or hosts can be included in the
list.

Active

Setting

Description

Factory Default

Enable/Disable

This checkbox enables or disables the rule for allowed subnet
settings.

Disable

IP

Setting

Description

Factory Default

IP address for allowed
subnet definition

The IP address of the subnet definition. Hosts in this subnet can
be accessed by other hosts or wireless clients in the same
subnet.

None

Netmask

Setting

Description

Factory Default

Netmask for allowed
subnet definition

The netmask of the subnet definition. Hosts in this subnet can
be accessed by other hosts or wireless clients in the same
subnet. You can also define the exception host by entering
255.255.255.255 in this field.

None

Protocol

Setting

Description

Factory Default

Protocol for allowed
subnet definition

The protocol of the subnet definition. Hosts in this subnet can
be accessed by other hosts or wireless clients in the same
subnet.

All

Port

Setting

Description

Factory Default

Port for allowed subnet
definition

The port range of the subnet definition. Hosts in this subnet can
be accessed by other hosts or wireless clients in the same
subnet.

None

WLAN Security Settings

The AWK-3131A-M12-RCC provides four standardized wireless security modes: Open, WEP (Wired Equivalent
Privacy), WPA (Wi-Fi Protected Access), and WPA2. Several security modes are available in the
AWK-3131A-M12-RCC by selecting Security mode and WPA type:

•

Open: No authentication, no data encryption.

•

WEP: Static WEP (Wired Equivalent Privacy) keys must be configured manually.

•

WPA/WPA2-Personal: Also known as WPA/WPA2-PSK. You will need to specify the Pre-Shared Key in the
Passphrase field, which will be used by the TKIP or AES engine as a master key to generate keys that
actually encrypt outgoing packets and decrypt incoming packets.

•

WPA/WPA2-Enterprise: Also called WPA/WPA2-EAP (Extensible Authentication Protocol). In addition to
device-based authentication, WPA/WPA2-Enterprise enables user-based authentication via IEEE802.1X.
The AWK-3131A-M12-RCC can support three EAP methods: EAP-TLS, EAP-TTLS, and EAP-PEAP.

«
...
26
27
28
29
30
...
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

i-bus KNX IPR/S 3.5.1

Brand: ABB Pages: 44

Brand: CAME Pages: 4

Brand: Mackie Pages: 2

Brand: Mackie Pages: 5

Brand: Barco Pages: 100

Brand: LAWO Pages: 154

Brand: Rane Pages: 4

EK-FC780 GTX Jetstream

Brand: ekwb Pages: 2

Brand: Renesas Pages: 941

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

DIRECTOR PRO series

Brand: MF DIGITAL Pages: 79

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brand: ICP DAS USA Pages: 8

Brand: EMTRUST Pages: 103

Brand: Network Critical Pages: 200

Brand: 3Com Pages: 53

Brand: iNetVu Pages: 20

Brand: ZyXEL Communications Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands