Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download | Manualshive

Page: 40 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-25

Favorite Profile

Setting

Description

Factory Default

Profile 1/
Profile 2

Choose your favorite profile to quickly switch RF type, channel,
transmission power, beacon interval, and beacon broadcast
status.

No Extended Control

Advanced Settings

Several advanced functions are available to increase the functionality of your AWK-3131A-M12-RCC and
wireless network system. A VLAN is a collection of clients and hosts grouped together as if they were connected
to the broadcast domains in a layer 2 network. The DHCP server helps you deploy wireless clients efficiently.
Packet filters provide security mechanisms, such as firewalls, in different network layers. Moreover, the
AWK-3131A-M12-RCC can support STP/RSTP protocol to increase reliability across the entire network, and
SNMP support can make network management easier.

«
...
38
39
40
41
42
...
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 10

Brand: Fracarro Pages: 12

MultiConnect SE MTS2EA

Brand: Multitech Pages: 2

AirStation WHR-G300N

Brand: Hornington Pages: 6

Supero SAS-826A

Brand: Supero Pages: 16

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

kontron COMe-cEL6

Brand: S&T Pages: 99

Brand: Parker Pages: 50

Brand: Caen Pages: 14

Brand: Nilox Pages: 66

Brand: Kontron Pages: 62

Brand: Navitar Pages: 1

Brand: Renesas Pages: 67

Brand: ADTRAN Pages: 136

Brand: Planet Pages: 16

Brand: Vivotek Pages: 46

Brand: Jetter Pages: 20

Brand: Billion Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands