Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download | Manualshive

Page: 42 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-27

Configuring Virtual LAN

VLAN Settings

To configure the AWK’s VLAN, use the VLAN Setting page to configure the ports.

Management VLAN ID

Setting

Description

Factory Default

VLAN ID
ranges from
1 to 4094

Set the management VLAN of this AWK.

1

Port

Type

Description

Trunk Port

LAN

This port is the LAN port on the AWK.

Yes

WLAN

This is a wireless port for the specific SSID. This field will refer
to the SSID that you have created. If more SSIDs have been
created, new rows will be added.

Port PVID

Setting

Description

Factory Default

VLAN ID ranging from 1
to 4094

Set the port’s VLAN ID for devices that connect to the port. The
port can be a LAN port or WLAN ports.

1

VLAN Tagged

Setting

Description

Factory Default

A comma-separated list
of VLAN IDs. Each of
the VLAN IDs range
from 1 to 4094.

Specify which VLANs can communicate with this specific VLAN. (Empty)

NOTE

The VLAN feature can allow wireless clients to manage the AP. If the VLAN Management ID matches a VLAN
ID, then those wireless clients who are members of that VLAN will have AP management access.

CAUTION: Once a VLAN Management ID is configured and is equivalent to one of the VLAN IDs on the AP, all
members of that User VLAN will have management access to the AP. Be careful to restrict VLAN membership
to those with legitimate access to the AP.

«
...
40
41
42
43
44
...
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

SR8800 IM-FW-II

Brand: H3C Pages: 107

Brand: 3Com Pages: 12

Brand: H3C Pages: 16

H3C S3600 Series

Brand: H3C Pages: 10

Brand: H3C Pages: 42

Brand: H3C Pages: 2

H3C S7500E Series

Brand: H3C Pages: 34

Brand: H3C Pages: 33

Brand: H3C Pages: 14

Brand: H3C Pages: 56

H3C S7500E Series

Brand: H3C Pages: 112

Brand: H3C Pages: 15

SR8800 IM-FW-II

Brand: H3C Pages: 5

H3C S7500E Series

Brand: H3C Pages: 50

Brand: H3C Pages: 37

Brand: H3C Pages: 4

Brand: H3C Pages: 5

Brand: H3C Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands