13
Section 6 — water SyStemS
camelot 2007
4. Connect the other end of the hose to the
water source.
5. Turn the Water Control
Valve to the “Tank Fill”
position.
6. Turn on water at the
water source. The water
should be audible as the
fresh water tank fills.
Monitor the tank filling
by using the water service center
monitor or monitor panel located inside
the motorhome.
7. Frequently press the “Tank Test”
switch and read the scale as the fresh
water tank fills. The fresh water tank is
nearing full when the 2/3 fresh water
tank light illuminates. Do not leave the
motorhome unattended while filling the
fresh water tank.
8. The tank is nearing full when the light
marked “F” illuminates. When the tank
is completely full, water will flow out
an overflow tube under the motorhome.
9. Turn off water supply and disconnect
the potable hose. Store the hose with
both ends connected to prevent debris
from entering the hose.
10. Return the Water Control Valve to “City
Water” position.
Water tank - freSH graVIty fIll
The gravity fill inlet allows fluids to be
introduced directly into the fresh water tank.
Water can be poured directly from a container
into the fresh water tank. The gravity fill inlet
can be used to pour disinfecting solution into
the fresh water tank or when using potable RV
antifreeze to winterize the fresh water system.
Use only potable water sources, solutions and
delivery systems when using the gravity fill
inlet. Fresh water tank is located in a roadside
compartment.
Filling the Tank:
1. Unscrew fill cap
taking care to keep
cap and inlet clean.
2. Insert potable water
hose into inlet.
3. Fill tank until water
overflows from inlet.
NOTE
When filling tank do not leave hose
unattended.
City Water Hook-up
When connecting the motorhome to fresh
waster, use a hose manufactured and labeled for
potable water to ensure the hose
will not flavor the water.
1. If the motorhome has an
optional hose reel, pull
hose out. Connect the
pressure regulator and
hose to the water source
and proceed to #4. Arrow
on pressure regulator must
be pointed toward reel. If
motorhome does not have a
hose reel, proceed to #2.
2. Install the pressure regulator on the
City/Fresh Water Fill valve. Arrow
on regulator must be pointed toward
valve.
3. Connect the water hose to the pressure
regulator.
4. Water Control Valve should be in the
“City Water” position.
5. Turn on the water at the water source.
6. The water pump can either be OFF or
ON. It will not affect the water pump
to leave it on.
7. Open each faucet, one at a time, to rid
any trapped air inside the pipes.
CAUTION
Some water sources develop high water
pressure, particularly in mountainous
regions. High water pressure is anything
over 55 psi (pounds per square inch).
Excessive water pressure may cause
leaks in water lines and/or damage the
water heater.
Water pump
The water pump
pressurizes the fresh water
system when not connected
to city water. The water
pump is self-priming,
operating on demand as
water is used. The water
pump is located in the water
service center.
Water pump inlet
screen:
Located on
water pump in water
service center. Clean
every two months.
040586
040460o
040460p
040483f
040480e
Summary of Contents for Camelot 2007
