Molecular Devices StakMax User Manual Download Page 40

Page: 40 / 146

Installation and Setup of StakMax® system

0112-0133 Rev B

To run a SpectraTest

reader validation plate, you must manually place it

in the read drawer. Do not attempt to load a SpectraTest reader validation

plate using the StakMax instrument.

Stopping the StakMax

Instrument in an Emergency

In an emergency, press the

Emergency Stop

button (yellow button) in the

main StakMax window or press the green

Power/Reset

button that is

located on the front-left side of the instrument. Pressing either of these

buttons immediately stops the StakMax instrument and the reader.

Setting Preferences

You can set preferences in the SoftMax Pro and the StakMax software

interface. The SoftMax Pro preferences primarily set how the data is

handled and saved (for example, export format and AutoSave), while the

StakMax preferences set the robotic functions (for example, barcoding

and scripting).

To set StakMax

Preferences

To set preferences in the StakMax software interface, open the StakMax

software interface and click

Preferences

To set SoftMax

Pro Preferences

On the main menu, select File > Edit > Preferences.

In the Preferences window, select the preferences, and then click

OK. See

Figure 2-26

Note:

If you leave a plate in the reader and try to run a new plate, the

system will place the plate on top of the existing plate in the carriage. If

this occurs, the reader will jam when it is closed. Although this will not

damage the reader, it is best to prevent this from happening.

Note:

If you use the Power/Reset button to stop the instrument, AutoSave

does not occur. If you stop the stacker while it is still in motion and before a

read, there is no data to be saved. If you stop the stacker during a read, data is

not autosaved, but you can manually save data in the SoftMax Pro software.

Summary of Contents for StakMax



















































































































































Search results

Summary of Contents for StakMax

Reviews:

Related manuals for StakMax

Brands by name

Popular brands

Molecular Devices StakMax, User Manual

Search results

Summary of Contents for StakMax

Reviews:

Related manuals for StakMax

Brands by name

Popular brands