Molecular Devices StakMax User Manual Download Page 52

Page: 52 / 146

Installation and Setup of SpectraMax® L instrument

0112-0133 Rev B

Accessory kit

•

StakMax

Plate Handling System User Guide

•

USB cable

•

Single Plate Adapter

•

Instrument-specific baseplate

•

100-240–volt power supply

•

Region-specific power cable for power supply

•

1 package of 5 Microplates

•

Allen wrench

•

2 Phillips-head screws

Instrument box

•

StakMax instrument

•

Barcode reader(s) (installed on instrument as configured)

•

20-plate magazines (if purchased)

Installing the StakMax

Instrument

Before installing the StakMax instrument, make sure that the foam blocks

have been removed from the input stack and the arm.

To install the StakMax

instrument

Unpack the StakMax system and make sure that all of the

components listed in

Components on page 51

are present.

Note:

40-plate and 50-plate magazines are shipped in a separate box.

WARNING! Make sure the power cord is not connected to the instrument
prior to installation or relocation of the instrument.

WARNING! Do not touch or loosen any screws or parts other than those
specifically designated in the instructions because this may cause
misalignment and this voids the instrument warranty.

Summary of Contents for StakMax



















































































































































Search results

Summary of Contents for StakMax

Reviews:

Related manuals for StakMax

Brands by name

Popular brands

Molecular Devices StakMax, User Manual

Search results

Summary of Contents for StakMax

Reviews:

Related manuals for StakMax

Brands by name

Popular brands