11
11-69
Lubricant and/or sealant
Special tools (Unit: mm)
Removal procedure
Removal: Vacuum pump
•
The vacuum pump also serves for positioning the balance shaft
LH. Therefore, before removing the vacuum pump, hold the bal-
ance shaft in position by the following procedure.
•
Align the pointer A to between the inscribed lines (
I
and
IV
or 1
and 4) on the flywheel. (Place No. 1 cylinder piston at the top
dead center on compression stroke.)
•
Remove the upper crankcase plug.
•
Mark a screwdriver or the like (
φ
4.5 mm or less) at a point 40
mm apart from its tip.
•
Insert the screwdriver or the like (
φ
4.5 mm or less) into the plug
hole until it lightly touches the balance shaft LH.
CAUTION
• Do not press the screwdriver hard against the balance shaft
LH, as this may damage No. 1 journal of the balance shaft.
•
Put the tip of the screwdriver or the like into the shaft supporting
hole at No. 1 journal of the balance shaft.
•
This insertion depth of the screwdriver or the like into the shaft
supporting hole should be 5 mm.
•
Remove the vacuum pump with the screwdriver or the like in-
serted in the hole.
Installation: Fan pulley
•
Put
in position on the studs of the fan pulley and fix the tool
by using nuts.
•
Loosen the fan pulley mounting nut while holding
.
Mark
Points of application
Specified lubricant and/or sealant
Quantity
O-ring
Engine oil
As required
Front oil seal lip
Front case installation surfaces
ThreeBond 1207C or D
As required
Mark
Tool name and shape
Part No.
Application
Holding bar
MH062970
Holding of fan pulley
A
B
114
φ
9
Summary of Contents for Fuso CANTER FE85DE6SLGP
