manualshive.com logo in svg

Mitsubishi 32172, User Manual

Share
Download
Mitsubishi 32172 User Manual Download Page 786

21

21-4

Rev.1.0

JTAG

21.3  JTAG Registers

21.3  JTAG Registers

21.3.1  Instruction Register (JTAGIR)

The Instruction Register (JTAGIR) is a 6-bit register to hold instruction code. This register is set in

IR path sequence. The instructions set in this register determine the data register to be selected in

the subsequent DR path sequence.

When test is reset (to initialize the test circuit), the initial value of this register is b'000010 (IDCODE

instruction). After a test reset, the IDCODE Register is selected as the data register until an

instruction code is set by an external device. In "Capture-IR" state, this register always has

b'110001 (fixed value) loaded into it. Therefore, when in "Shift-IR" state, no matter what value was

set in this register, b'110001 is always output from the JTDO pin (sequentially beginning with LSB).

However, this value normally is not handled as instruction code.

Shown below is outside the scope of guaranteed operations. Note that if this operation is

performed, the device may inadvertently handle b'110001 as instruction code, which makes it

unable to operate normally.

[Capture-IR]   

→

   [Exit1-IR]   

→

   [Update-IR]

The 32172/32173's JTAG interface supports the following instructions:

•  Three instructions stipulated as essential in IEEE 1149.1 (EXTEST, SAMPLE/PRELOAD,

   BYPASS)

•  Device ID register access instruction (IDCODE)

Table 21.3.1  JTAG Instruction List

Instruction Code

Abbreviation

Operation

b'000000

EXTEST

Tests circuit/board-level connections outside the chip.

b'000001

SAMPLE/PRELOAD

Samples operating circuit status and outputs the sampled status

from JTDO pin, while at the same time entering the data used for

boundary-scan test from the JTDI pin and presets it in Boundary

Scan Register.

b'000010

IDCODE

Selects ID Code Register and outputs device and manufacturer

identification data from JTDO pin.

b'111111

BYPASS

Selects Bypass Register and inspects or sets data.

Note 1: Do not set any other instruction code.

Note 2: For details about "IR path sequence," "DR path sequence," "Test reset," "Capture-IR" state,

  "Shift-IR" state, "Exit1-IR" state, and "Update-IR" state, refer to Section 21.4.

Summary of Contents for 32172











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands