Mitsubishi MOTORS Lancer 2005 Workshop Manual Supplement Download Page 24

Page: 24 / 109

MPI <4G63>

Troubleshooting

13D-19

To the next page

Check the harness wire between the
throttle position sensor and the
engine-A/T-ECU, and repair if
necessary.

Check the following connector:

C-126

Repair

(3) NG

Adjust the throttle position sensor.
(Refer to P.13D-98.)

Check the harness wire between the
throttle position sensor and the
engine-A/T-ECU.

(1) NG

Check the following connector:

C-124

Repair

(2) NG

Measure at throttle position sensor
connector B-06.

Use test harness (MB991536) to
connect the connector, and
measure at the pick-up harness.

Ignition switch: ON

(1) Voltage between terminal 1 and

earth

OK:

4.9

5.1 V

(2) Voltage between terminal 4 and

earth

OK:

0.5 V or less

(3) Voltage between terminal 2 and

earth

OK:

Accelerator pedal fully re-
leased: 0.335

0.935 V

Accelerator pedal fully de-
pressed: 4.4

5.3 V

Check the trouble symptoms.

Replace the engine-A/T-ECU.

Check the trouble symptoms.

Replace the engine-A/T-ECU.

Check the harness wire between the
throttle position sensor and the
engine-A/T-ECU.

Repair

Check the following connector:

C-124

Repair

Check the harness wire between the
throttle position sensor and the
engine-A/T-ECU, and repair if
necessary.

Repair

Measure at throttle position sensor
connector B-06.

Disconnect the connector and
measure at the harness side.

(1) Voltage between terminal 1 and

earth
(Ignition switch: ON)

OK:

4.9

5.1 V

(2) Resistance between terminal 4

and earth

OK:

or less

(1) NG

Measure at engine-A/T-ECU
connector C-124.

Measure the voltage at the
engine-A/T-ECU terminals.

Ignition switch: ON

Voltage between terminal 46 and
earth

OK:

4.9

5.1 V

Check the following connector:

C-124

(2) NG

Check the following connector:

C-124

Repair

Check the harness wire between the
throttle position sensor and the
engine-A/T-ECU.

Repair

From the previous page

Summary of Contents for Lancer 2005














































































































Search results

Summary of Contents for Lancer 2005

Reviews:

Related manuals for Lancer 2005

Brands by name

Popular brands

Mitsubishi MOTORS Lancer 2005, Workshop Manual Supplement

Search results

Summary of Contents for Lancer 2005

Reviews:

Related manuals for Lancer 2005

Brands by name

Popular brands