Mitsubishi MOTORS Lancer 2005 Workshop Manual Supplement Download Page 34

Page: 34 / 109

MPI <4G63>

Troubleshooting

13D-29

Code No. 41 Injector system

Probable cause

Range of Check

Fuel cut and injector not in forced drive (actuator test) mode.

The engine speed is 50

1,000 r/min

The throttle position sensor output voltage is 1.15 V or less.

Set Condition

Surge voltage of injector coil is not detected for 4 seconds.

Malfunction of the injector

Improper connector contact, open circuit or short-cir-
cuited harness wire of the injector circuit

Malfunction of the engine-A/T-ECU

Replace the engine-A/T-ECU.

Use an analyzer to measure the signal waveform at injector
connector B-02, B-03, B-04, B-05.

Use a test harness (MB991348) to connect the connector, and
measure at the pick-up harness side.

Engine: Idling

The voltage between terminal 2 and earth

OK:

A normal waveform should be displayed as described
on P.13D-83 (INSPECTION PROCEDURE USING
AN ANALYZER).

Intermittent malfunction
(Refer to GROUP 00

Points to Note for Intermittent Malfunctions.)

Check the trouble symptoms.

Measure at the engine-A/T-ECU connector C-122.

Disconnect the connector, and measure at the harness side.

Voltage between 1, 2, 9, 24 and earth (Ignition switch: ON)

OK:

System voltage

Check the harness wire between the engine-A/T-ECU and the
injector connector, and repair if necessary.

Check the following connector:

C-122

Repair

Measure at the injector connector B-02, B-03, B-04, B-05.

Disconnect the connector, and measure at the harness side.

Voltage between 1 and earth (Ignition switch: ON)

OK:

System voltage

Check the harness wire between the engine control relay and the
injector connector, and repair if necessary.

Check the injector. (Refer to P.13D-101.)

Replace

Check the following connectors:

B-02, B-03, B-04, B-05

Repair

M.U.T.-

II/III

Actuator Test

01 No. 1 injector
02 No. 2 injector
03 No. 3 injector
04 No. 4 injector

OK:

The idling condition should change

Intermittent malfunction
(Refer to GROUP 00

Points to Note for Intermittent Malfunctions.)

Summary of Contents for Lancer 2005














































































































Search results

Summary of Contents for Lancer 2005

Reviews:

Related manuals for Lancer 2005

Brands by name

Popular brands

Mitsubishi MOTORS Lancer 2005, Workshop Manual Supplement

Search results

Summary of Contents for Lancer 2005

Reviews:

Related manuals for Lancer 2005

Brands by name

Popular brands