Mitsubishi MOTORS Lancer 2005 Workshop Manual Supplement Download Page 39

Page: 39 / 109

MPI <4G63>

Troubleshooting

13D-34

Code No. 64 Alternator FR terminal system

Probable cause

Range of Check

During the engine running.

Set Condition

Input voltage from the alternator FR terminal is system voltage for 20
seconds.

Open circuit in alternator FR terminal circuit

Malfunction of the engine-A/T-ECU

Replace the engine-A/T-ECU.

Intermittent malfunction
(Refer to GROUP 00

Points to

Note for Intermittent Malfunctions.)

Check the trouble symptoms.

Replace the alternator.

Check the trouble symptoms.

Check the harness wire between the
alternator connector and the
engine-A/T-ECU.

Repair

Check the following connectors:

B-18, C-124

Replace

Measure at the alternator connector
B-26.

Use test harness (MB991519) to
connect the connector, and
measure at the pick-up harness.

Engine: Idling (After warming up)

Radiator fan: Not operating

The voltage between terminal 4
and earth

OK:

The voltage drops when
the headlamps are turned
on.

Check the trouble symptoms.

Replace the engine-A/T-ECU.

Check the harness wire between the
alternator connector and the
engine-A/T-ECU.

Repair

Check the following connector:

C-124

Repair

Check the harness wire between the
alternator connector and the
engine-A/T-ECU, and repair if
necessary.

Repair

Check the following connectors:

B-18, C-124

Measure at the engine-A/T-ECU
connector C-124.

Measure the voltage at the
engine-A/T-ECU terminal.

Ignition switch: ON

The voltage between terminal 54
and earth

OK:

10 V

Measure at the alternator connector
B-26.

Use test harness (MB991519) to
connect the connector, and
measure at the pick-up harness.

Ignition switch: ON

The voltage between terminal 4
and earth

OK:

10 V

Check the following connector:

B-26

Repair

Summary of Contents for Lancer 2005














































































































Search results

Summary of Contents for Lancer 2005

Reviews:

Related manuals for Lancer 2005

Brands by name

Popular brands

Mitsubishi MOTORS Lancer 2005, Workshop Manual Supplement

Search results

Summary of Contents for Lancer 2005

Reviews:

Related manuals for Lancer 2005

Brands by name

Popular brands