Mitsubishi MOTORS Lancer 2005 Workshop Manual Supplement Download Page 97 | Manualshive

Page: 97 / 109

background image

MPI <4G63>

ï

On-vehicle Service

13D-92

NOTE
(1) The engine speed may be 20 to 100 r/min lower

than indicated above for a new vehicle [driven
approximately 500 km or less], but no adjustment
is necessary.

(2) If the engine stalls or the engine speed is low even

though the vehicle has been driven approximately
500 km or more, it is probable that deposits are
adhered to the throttle valve, so clean it (Refer to
P.13D-90.)

6.

If not within the standard value range, turn the speed
adjusting screw (SAS) to make the necessary adjustment.

NOTE
If the idling speed is higher than the standard value range
even when the SAS is fully closed, check whether or
not there is any indication that the fixed SAS has been
moved. If there is an indication that it has been moved,
adjust the fixed SAS.

7.

Press the M.U.T.-

II/III

clear key, and release the ISC

servo from the actuator test mode.

NOTE
Unless the ISC servo is released, the actuator test mode
will continue 27 minutes.

8.

Turn the ignition switch to ”LOCK” (OFF) position.

9.

Disconnect the M.U.T.-

II/III

.

10. Start the engine again and let it run at idle speed for

about 10 minutes; check that the idling condition is normal.

FUEL PRESSURE TEST

1.

Release residual pressure from the fuel pipe line to prevent
fuel gush out.

Caution
Cover the hose connection with rags to prevent splash
of fuel that could be caused by some residual pressure
in the fuel pipe line.

2.

Disconnect the high-pressure fuel hose at the delivery
pipe side.

3.

Assemble the fuel pressure measurement tools as follows.

<When using the fuel pressure gauge set (special tool)>
(1) Remove the union joint and bolt from the special

tool adaptor hose (MD998709) and attach the special
tool hose adaptor (MD998742) to the adaptor hose.

(2) Via a gasket, install the special tool fuel pressure

gauge set (MB991637 or MB991981) into the special
tool that has already assembled as described in (a)
above.

MB991637

Gasket

MD998709

MD998742

High-pressure
fuel hose

Delivery
pipe

«
...
95
96
97
98
99
...
»

Summary of Contents for Lancer 2005














































































































Reviews:

No comments

Related manuals for Lancer 2005

Brand: Falcon Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Wallbox Pages: 7

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brand: Yakima Pages: 12

Brand: Romik Pages: 6

2011 Civic Sedan

Brand: Honda Pages: 5

990E0-54P56-000

Brand: Suzuki Pages: 12

DLD Wide Range II

Brand: VDO Pages: 84

TravelCharge Companion GO-Plus

Brand: Wagan Pages: 3

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brand: mtf TRANSPORT SYSTEM Pages: 9

Brand: SAN HIMA Pages: 10

Brand: Prorack Pages: 14

Brand: Acura Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands