Mitsubishi MOTORS Lancer 2005 Workshop Manual Supplement Download Page 50

Page: 50 / 109

MPI <4G63>

Troubleshooting

13D-45

Check the following items.

Check the ignition coil, spark plugs, spark plug cables.

Check the purge control system.

Check the EGR control system.

Check the compression pressure.

Check if foreign materials (water, alcohol, etc.) got into fuel.

Check the ignition timing.
(Refer to GROUP 11E

On-vehicle Service.)

Check that the crank angle sensor is installed properly.

M.U.T.-

II/III

Data list

45 ISC servo position (Refer to P.13D-66.)

Adjust the basic idle speed. (Refer to P.13D-91.)

M.U.T.-

II/III

Data list

28 A/C switch (Refer to P.13D-66.)

Check the A/C switch and A/C relay system.
(Refer to P.13D-63, INSPECTION PROCEDURE 31.)

M.U.T.-

II/III

Data list

27 Power steering fluid pressure switch (Refer to P.13D-66.)

Check the power steering
fluid pressure switch sys-
tem. (Refer to P.13D-63,
INSPECTION

PROCE-

DURE 30.)

M.U.T.-

II/III

Data list

11 Oxygen sensor (front)

OK:

Changes between 0

400 mV and 600

1,000 mV during

idling

Check the fuel pressure.
(Refer to P.13D-92.)

1. Inspect the intake of

air into the air intake
system.

Broken intake man-
ifold gasket

Broken vacuum hose

PCV valve does not
operate.

Broken air intakehose

2. Check the injector for

clog.

M.U.T.-

II/III

Data list

11 Oxygen sensor (front)

OK:

600

1,000 mV during sudden racing

Check the oxygen sensor (front) system.
(RefertoP.13D-13,INSPECTION PROCEDUREFORDIAGNOSIS
CODE 11.)

M.U.T.-

II/III

Data list

59 Oxygen sensor (rear)

Transmission: D range

Driving with throttle widely open

OK:

600

1,000 mV

Check the oxygen sensor (rear) system.
(RefertoP.13D-32,INSPECTION PROCEDUREFORDIAGNOSIS
CODE 59.)

From the previous page

Summary of Contents for Lancer 2005














































































































Search results

Summary of Contents for Lancer 2005

Reviews:

Related manuals for Lancer 2005

Brands by name

Popular brands

Mitsubishi MOTORS Lancer 2005, Workshop Manual Supplement

Search results

Summary of Contents for Lancer 2005

Reviews:

Related manuals for Lancer 2005

Brands by name

Popular brands