manualshive.com logo in svg

Mitsubishi MOTORS Lancer 2004, Workshop Manual

Share
Download
Mitsubishi MOTORS Lancer 2004 Workshop Manual Download Page 215

DRIVE SHAFT ASSEMBLY

FRONT AXLE

26-21

INSPECTION

M1261003800130

•

Check the drive shaft for damage, bending or 
corrosion.

•

Check the drive shaft spline part for wear or 
damage.

•

Check the spider assembly for roller rotation, 
wear or corrosion.

•

Check the groove inside TJ case for wear or 
corrosion.

•

Check the dynamic damper for damage or 
cracking.

•

Check the boots for deterioration, damage or 
cracking.

BJ BOOT (RESIN BOOT) REPLACEMENT

M1261005200361

1. Remove the boot bands (large and small).

NOTE: The boot bands cannot be re-used.

2. Remove the BJ boot.
3. Wrap a plastic tape around the shaft spline, and 

assemble the boot band and BJ boot.

4. Align the centre groove on the BJ boot small end 

with the shaft groove.

5. Turn the adjusting bolt on special tool boot band 

crimping tool (MB991561) so that the size of the 
opening (W) is at the standard value.

Standard value (W): 2.9 mm

<If it is larger than 2.9 mm> Tighten the 

adjusting bolt.

<If it is smaller than 2.9 mm> Loosen the 

adjusting bolt.

NOTE: The value of W will change by 
approximately 0.7 mm for each turn of the 
adjusting bolt.
NOTE: The adjusting bolt should not be turned 
more than once.

6. Position the BJ boot band (small) so that there is 

even clearance at either end (A and B).

AC102658

AC102659

AC102660

W

MB991561

Stopper

Adjusting bolt

AC

AC102661AC

Boot

A

Boot band
(small)

B

Projection

Summary of Contents for Lancer 2004































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands