manualshive.com logo in svg

Mitsubishi Electric Q172CPU, Programming Manual

Share
Download
Mitsubishi Electric Q172CPU Programming Manual Download Page 252

 
 

 

 

6 - 23

6   PARAMETERS FOR POSITIONING CONTROL 

 

6.3.17 Zero speed 

This parameter sets the speed at which the motor speed is judged as "0". 

 

6.3.18 Error excessive alarm level 

This parameter sets the range in which the alarm for excessive droop pulses is output. 

 

6.3.19 Optional function 5 

(1)   PI-PID control switching 

This parameter sets the condition under which switching from PI to PID control, or 
from PID control to PI control, is valid. 

 

(2)   Servo readout characters 

When the optional parameter unit is connected, set whether the screen display on 
the parameter unit is Japanese or English. 

 

6.3.20 PI-PID control switching position droop 

This parameter sets the position droop value (Number of pulses) which PI control is 
switched to PID control during position control. 
The setting becomes valid when switching in accordance with the droop during position 
control is made valid using the setting for PI-PID control switching by optional function 
5.  

 

6.3.21 Torque control compensation factor 

This parameter is used to expand the torque control range up to the speed control 
value at the torque control. (MR-H BN only) 
If a large value is set, the speed limit value may be exceeded and the motor may 
rotate. 

 

6.3.22 Speed differential compensation 

This parameter sets the speed differential compensation value of the real speed loop. 
In PI (proportional integration) control, if the value for speed differential compensation 
is set at 1000, the range for normal P (proportional) control is valid; if it is set to a value 
less than 1000, the range for P (proportional) control is expanded. 

 
 
 

Summary of Contents for Q172CPU



























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands