Mitsubishi Electric NZ2GN2B1-32D, User Manual

Page: 58 / 268

56
3 SPECIFICATIONS
3.3 Performance Specifications
NZ2GN2B1-32T transistor output module
*1 The performance specifications vary depending on firmware versions of modules used. (

Page 256 Added and Changed Functions)
*2 Use bar solderless terminals for wiring.
*3 Only one wire can be inserted into a wire insertion opening for the terminal block for module power supply and FG. Multiple wires cannot
be connected to a terminal. Connecting two or more wires may cause a poor contact.
*4 This value indicates the number of points set by default when the module is dragged and dropped to the network map in the CC-Link IE
TSN Configuration window. According to the function used, set an appropriate number of points. (  Page 227 Output module (32-
point module))
Item NZ2GN2B1-32T
Station type Remote station
Authentication Class Authentication Class B
Network topology Line topology, star topology, mixture of star topology and line topology, ring topology
*1
Number of output points 32 points
Rated load voltage 12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
Max. load current 0.5A/point, 5A/common
Maximum inrush current Current is limited by the overload protection function.
Leakage current at OFF 0.1mA or less
Max. voltage drop at ON 0.3VDC (TYP.) 0.5A, 0.6VDC (MAX.) 0.5A
Output response time OFF

ON 0.1ms or less
ON

OFF 0.8ms or less (resistive load)
Surge suppressor Zener diode
External power supply for
output part Voltage 12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
Current 40mA or less (TYP. 24VDC per common) External load current is not included.
Withstand voltage 510VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10M

or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise immunity Noise voltage 500Vp-p, noise width 1

s, noise frequency 25 to 60Hz (DC type noise simulator
condition)
Protection degree IP2X
Wiring method for common 32 points/common (Common terminal: terminal number 34) (1-wire, screw terminal block type)
Sink type
Protection function Overload protection
function Limited current when detecting overcurrent: 1.5 to 3.5A/point
Activated to each point.
Overheat protection
function Activated to each point.
External interface Communication part RJ45 connector
Module power supply part Terminal block for module power supply and FG (2-piece spring clamp terminal block)
I/O part 34-point two-piece terminal block
Tightening torque range for terminal screw (M3

5.2 screw): 0.43 to 0.57N

m
Tightening torque range for terminal block mounting screw (M3.5 screw): 0.68 to 0.92N

m
Applicable wire size For power supply Stranded wire: 0.3 to 1.5

(22 to 16 AWG), terminal slot size: 2.4mm

1.5mm
*2
For I/O Stranded wire: 0.3 to 2.0

(22 to 14 AWG)
Applicable solderless
terminal Terminal block for module
power supply and FG
*3

Page 127 Applicable solderless terminal
Terminal block for output  Page 139 Applicable solderless terminal
Multicast filter Available
*1
Cyclic transmission RX/RY points 32 points
RWr/RWw points 4 points
*4
Module power supply Voltage 24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
Current 120mA or less (24VDC, all points ON)
Weight 0.29kg