manualshive.com logo in svg

MINOS T-MDR 1000, Operating Manual, Page: 66 / 87

Share
Download
MINOS T-MDR 1000 Operating Manual Download Page 66

© Copyright

 MINOS DIS TICARET LIMITED SIRKETI., 2020. All  rights reserved. Reprinting, even of sections, only possible with the approval of

 

MINOS DIS TICARET LIMITED SIRKETI.

                                                        Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020 

 

Noise and/or 
vibration from 
machine 

● Blades worn or 
damaged 
● Bearings worn or 
damaged 
● Rotor(s) damaged 
● Rotors/blades 
incorrectly installed 
(incorrect rotor 
arrangement and/or 
blades orientation) 
● Front of the machine 
not levelled to the back 
● Machine not stable at 
sides 
● Hard soil 

● Replace blades 
● Replace bearings 
● Repair/replace rotor(s) 
● Install rotors/blades 
correctly (follow rotors 
arrangement shown in the 
manual and /or reinstall 
blades with correct 
orientation)  
● Adjust 3-point tractor top 
link making input connection 
shaft parallel to the ground 
● Lock tractor lifting arms to 
prevent machine swinging 
● Reduce ground speed

 

Rotor stops turning 

● Slip clutch slipping 
● Broken gear(s) in 
gearbox/ 
/gears transmission 
trough 

● Reduce load to the machine 
or adjust slip clutch 
● Replace gear(s) 

Smoke and/or hot 
smell from the 
machine 

● Debris wrapped 
around blades and/or 
rotors 
● Low oil level 
● Slip clutch slipping 

● Remove debris 
● Add oil 
● Reduce load to machine or 
adjust slip clutch 

Gearbox/gears 
transmission trough 
overheating 

● Low oil level 
● Hard soil 

● Add oil 
● Reduce ground speed 

Blades wear 
frequently 

● Muddy or sandy soil 

● Reduce ground speed 

Blades break 
frequently 

● Stony soil 

● Reduce ground speed 

Oil leaking from 
gearbox/ gears 
transmission trough 

● Gearbox/gears 
transmission trough 
overfilled 
● Loose filling/drain plug 
● Damaged breather 
plug 
● Damaged seals 

● Drain to proper level 
● Tighten filling/drain plug 
● Replace breather plug 
● Replace seals 

58 

Summary of Contents for T-MDR 1000
























































































Reviews:

No comments