manualshive.com logo in svg

MINOS T-MDR 1000, Operating Manual, Page: 6 / 87

Share
Download
MINOS T-MDR 1000 Operating Manual Download Page 6

© Copyright

 MINOS DIS TICARET LIMITED SIRKETI., 2020. All  rights reserved. Reprinting, even of sections, only possible with the approval of

 

MINOS DIS TICARET LIMITED SIRKETI.

                                                        Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020 

 

 

 

Dear Customer!

 

You  have  purchased  one  of  the  best  built,  most  reliable  power  harrow  available  and  you 
have chosen it from our wide product range. Congratulations! We strive to provide you with 
a rugged, durable unit which is simple to maintain and we are sure that you will be satisfied 
with it. We sincerely thank you for your confidence.  

With  their  strong,  powerful  and  reliable  structure,  easy-to-use  operation  and  wide  model 
range  that  is  able  to  meet  any  kind  of  needs,  Minos  mini  power  harrow 

is  an  essential 

equipment

 

that

 prepares soil for seeding/ planting. In one pass the soil is broken up, weeds 

and scrub growth are uprooted, 

tillage and prepare the seedbed.

 

Any  person  who  will  be  operating  or  maintaining  this  machine  should  first  read  and 
understand this manual and meaning of all safety decals.  

This introducing and operating manual should always be available to those responsible for 
the operation and maintenance of this machine.  

It  is  the  owner’s  responsibility  to  provide  this  safety  information  to  his  operators  and 
employees.  

Any person who does not understand the safety and operation instructions contained in this 
manual should not be considered qualified to operate this machine. 

This  manual  has  been  designed  to  help  you  become  familiar  with  your  unit.  Before  you 
operate  your  unit,  be  sure  you  understand  and  follow  all  the  operation,  lubrication,  and 
safety instructions on the following pages in this manual. These have been written for your 
safety and convenience, and to keep your unit running trouble-free for many years. 

This manual should be considered a permanent part of your machine, and should remain 
with the machine if you sell it. 

In  the  event  that  you  experience  an  issue  that  has  not  been  addressed  in  this  manual, 
contact  our  company  for  help;  you  must  state  the  model  and  serial  number  of  you 

equipment

 in order for us to help you with your inquiry. This is necessary in order to resolve 

isues quicker and provide better services. 

Regards, 

MINOS DIS TICARET LIMITED SIRKETI 

Fatih Mah. 1191 Sok. No: 17/A 35414 Gaziemir/ 

İZMİR-TÜRKİYE 

Ph:

 +90 232 281 54 04 - 281 63 30 - 281 63 31

   Fax:

 +90 232 281 57 10

 

Web:

 www.minosagri.com  

E-mail:

 [email protected] 

 

THANK YOU FOR CHOOSING MINOS! 

Summary of Contents for T-MDR 1000
























































































Reviews:

No comments