manualshive.com logo in svg

MINOS T-MDR 1000, Operating Manual, Page: 16 / 87

Share
Download
MINOS T-MDR 1000 Operating Manual Download Page 16

© Copyright

 MINOS DIS TICARET LIMITED SIRKETI., 2020. All  rights reserved. Reprinting, even of sections, only possible with the approval of

 

MINOS DIS TICARET LIMITED SIRKETI.

                                                        Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020 

 

●  Secure  the  tractor  and  the  machine  against  unintional  start-up  and  rolling 
before  carrying  out  any  cleaning,  greasing  or  setting  work  on  universal  joint 
shaft driven implements or PTO shafts.  
 
● Deposit removed PTO shaft on the provided carrier!  
 
● When travelling in curves mind the permissible angling and sliding length! 
 
● When using the ground-related PTO take note that the PTO speed is related 
to the forward speed and that the sense of rotation reverses when backing up! 
 

 

 

 
 
●  Maintenance,  repair  work,  cleaning  and  disturbance  removing  may  only  be 
executed when the drive and the engine are switched off and the ignition key is 
pulled out! 
 
●  Regularly  check  the  nuts  and  bolts  for  a  firm  seat  and  retighten  them  as 
necessary. 
 
●  If  the  machine  or  parts  of  the  machine  are  raised,  secure  them  against 
unintentional lowering before cleaning, maintaining or repairing the machine. 
 
● When replacing work tools with blades, use suitable tools and gloves. 
 
● Dispose of oils, greases and filters in the appropriate way. 
 
●  Disconnect  the  cable  to  the  tractor  generator  and  battery,  before  carrying 
out electrical welding work on the tractor and on attached machines. 
 
● If safety devices succumb to usage, must be checked regularly and replaced 
in due time! 
 
● Use only genuine spare parts, they guarantee long lifetime of the machine! 
 

 

1.5- Maintenance and Repair 
 

8 

Summary of Contents for T-MDR 1000
























































































Reviews:

No comments