manualshive.com logo in svg

MINOS T-MDR 1000, Operating Manual, Page: 62 / 87

Share
Download
MINOS T-MDR 1000 Operating Manual Download Page 62

© Copyright

 MINOS DIS TICARET LIMITED SIRKETI., 2020. All  rights reserved. Reprinting, even of sections, only possible with the approval of

 

MINOS DIS TICARET LIMITED SIRKETI.

                                                        Document No: T-MDR.2020_I.O.M./ Date: 09.01.2020 

 

 

 

Regular  cleaning  of  the  mini  power  harrow  is  also  very  important  for  the  life 
time  of  the  machine.  Components  of  forage  cause  rusting  of  metal  parts  and 
other mechanical damages. Therefore clean and wash the machine after every 
use and lubricate it carefully.  

If  you  wash  machine  with  high  pressure  of  water,  distance  between  jet  of 
water and machine must be min. 0,7 m 

(see fig. 25)

. 

The machine should be washed, immediately after each use! 

 

 

Figure 25- A Safety distance between jet of water and machine. 

 
 
 
 
 
 
 
 
 

5.6- Cleaning & Washing 

 

 

54 

Summary of Contents for T-MDR 1000
























































































Reviews:

No comments