7-12
Error messages
Cause
Solution
To execute takeup, media cannot be automati-
cally cut.
When TAKEUP TIMING is set on roll media
detection, autocut is not executed. If putting
priority on autocut, set TAKEUP TIMING "OFF".
(
P.4-37)
A register mark cannot be detected.
(During the mark detection process after
detecting the medium)
Confirm the following items:
• Medium is not curled.
• The register mark detection start point is set
correctly.
(
P.4-15
)
• The register marks are printed in black against
a white background.
• There is no unnecessary patterns, dust, or dirt
between the register marks.
• Various settings regarding the register mark are
configured appropriately.
(
P.4-11
)
If all the above items are OK, contact our service
office or the distributor in your region.
A register mark cannot be detected.
(During copy cut of the mark)
• "MARK DETECT" and "JOG & <ENT> or
<END>"
are displayed alternately.
• "MARK SCALE" and "JOG & <ENT> or
<END>"
are displayed alternately.
Confirm the following items:
• When this error occurs, the light pointer stops at
the detection starting point. If the position is
found improper, move the light pointer to the
appropriate position using the JOG keys. Press
the ENTER key to make the machine perform
detection again.
• When using a soft medium or a large medium of
which the width exceeds 800 mm, increase the
pinch rollers (middle).
• When using a soft medium, set the length of
each side of the register mark to 8 mm or
above. Also, place the mark copies making a
clearance of 8 mm between each mark.
• Confirm that the register marks are printed in
black against a white background.
• Confirm that there is no unnecessary patterns,
dust, or dirt between the register marks.
• Confirm that the various settings regarding the
register mark are configured appropriately. P**
• When the media press is used, the medium
may be lifted. In this case, remove the media
press and try again.
If all the above items are OK, contact our service
office or the distributor in your region.
The origin is detected in the area outside of the
available printing area by the register mark
detecting process.
Place the register mark within the available
printing area.
An excessive load was applied to the X motor.
Turn OFF the power to the machine and turn it
ON again after a while.
If the same error message appears again,
contact our service office or the distributor in your
region.
An excessive load was applied to the Y motor.
An error due to an excessive current of the X
motor was detected.
An error due to an excessive current of the Y
motor was detected.
An error occurred in the capping control.
(Improper parameter adjustment value)
An error occurred in the wiper control.
* * * * E R R OR 3 5 - C * * * *
c u t N G W I N D
* * * * E R R OR 3 6 - C * * * *
M A R K D E T E C T
* * * * E R R OR 3 6 - C * * * *
J OG & < E N T > o r < E N D >
* * * * E R R OR 3 8 - C * * * *
M A R K S C A L E
* * * * E R R OR 3 7 - C * * * *
M A R K O R I G I N
* * * * * E R R OR 4 0
* * * * *
MO T O R A L A RM X
* * * * * E R R OR 4 1
* * * * *
MO T O R A L A RM Y
* * * * * E R R OR 4 2
* * * * *
X O V E R C U R R E N T
* * * * * E R R OR 4 3
* * * * *
Y O V E R C U R R E N T
* * * * * E R R OR 4 5
* * * * *
C A P P I N G : P A R A ME T E R
* * * * * E R R OR 4 6
* * * * *
W I P E R
Summary of Contents for CJV30-100BS
