Miele G 676 Operating Instructions Manual Download Page 70

Page: 70 / 84

Installing integrated "i" Dishwashers

Adjust the fixing bracket

The long holes in the machine door
outer panel must be aligned with the
matching markings on the template.

On the template

mark the height

of the top edge of adjacent kitchen
base unit doors.

Take off the fixing bracket.

Lay the door front down with the rear
side facing upwards.

Lay the bracket on the rear side of
the door front and adjust so that:

– the marks on the template for the

upper edge of the adjacent base
unit doors match the top edge of the
door front.

– The fixing bracket must be the same

distance from the left and right hand
side edges of the door front.

Use strips of adhesive tape to hold
the bracket in this position.

Installing integrated “i” Dishwashers

Summary of Contents for G 676





















































































Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands

Miele G 676, Operating Instructions Manual

Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands