Miele G 676 Operating Instructions Manual Download Page 66 | Manualshive

Page: 66 / 84

background image

Adjust the rear screw feet to the re-
quired height.

Higher = turn clockwise

Lower = turn anti-clockwise

Several turns are needed to adjust 1 mm
in height. A battery-powered screw-
driver could be used.

Adjust the front screw feet manually
or with a flat blade screwdriver.

It is easier to adjust the screw feet if the
weight of the dishwasher is not bearing
down on them.

If possible tip the machine slightly.

For fine adjustments it may be
necessary to press with a screw-
driver against the cogs of the feet.

Screw the feet out until the dishwasher
is right up against the underside of the
worktop, to which it will be screwed
later. Ensure that the dishwasher
stands level.

Installing integrated “i” Dishwashers

66

«
...
64
65
66
67
68
...
»

Summary of Contents for G 676





















































































Reviews:

No comments

Related manuals for G 676

Brand: Haier Pages: 13

Brand: Haier Pages: 12

Brand: Haier Pages: 15

Brand: Haier Pages: 18

Brand: Dacor Pages: 16

Brand: Zanussi Pages: 3

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 24

Brand: Zanussi Pages: 16

Brand: Clatronic Pages: 42

Brand: Hotpoint Pages: 20

Brand: Daewoo Pages: 17

Brand: NEW POL Pages: 20

Brand: Sammic Pages: 28

WashSmart WA4127G1

Brand: Fisher & Paykel Pages: 100

Brand: HERKULES Pages: 20

Brand: Monogram Pages: 88

Hotpoint HDA3400G

Brand: Hotpoint Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands