Miele G 676 Operating Instructions Manual Download Page 71

Page: 71 / 84

Installation integrated “i” Dishwashers

Drill the fixing holes to a depth of
about 10 mm, using a 2.5 mm drill bit.

Secure the fixing bracket to the door
front using the flat-head screws sup-
plied.

Take off the templates.

Keep the templates in case the dish-
washer is ever fitted with a new door
front.

Hang the door front into the slits in
the machine door outer panel.

Open the dishwasher door slightly.

Adjust the door front for the height
on one side and lightly screw in a
T20 Torx screw on this side.

Adjust the door front height on the
other side and also lightly screw in a
T20 Torx screw on this side.

Shut the dishwasher door.

Check the door front for correct align-
ment.

If necessary unscrew and readjust.

Once the door front is correctly posi-
tioned:

Open the dishwasher door.

Tighten all the Torx screws on the
sides.

Plug the openings for the fixing
screws using the plastic stoppers
provided.

Installing integrated “i” Dishwashers

Summary of Contents for G 676





















































































Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands

Miele G 676, Operating Instructions Manual

Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands