Miele G 676 Operating Instructions Manual Download Page 57 | Manualshive

Page: 57 / 84

background image

Installing a freestanding dishwasher

Adapting the height of the decor
panel supplied

Mark the measurement "X" on the left
and right hand side of the decor
panel and on the decor frame strips.

Take off and shorten the decor frame
strips (see Step 2), the decor panel
and the packing card.

Establishing the height of a new
decor panel

The decor panel supplied with the dish-
washer can be exchanged for a panel
to match your kitchen decor.

The new panel must have the following
measurements:

Width:
587 mm

Thickness:
Minimum 1 mm and maximum 4 mm.
The packing card originally supplied
behind the decor panel must be
removed for new panels with a thick-
ness of more than 2 mm.

Height:
604 mm minus "

X

" mm

Mark the measurement "

X

" on the left

and right hand side of the decor
frame.

Take off the decor frame strips (see
Step 2), the decor panel and the
packing card, and shorten the decor
frame strips, and the packing card (if
used).

Installing a freestanding dishwasher

57

«
...
55
56
57
58
59
...
»

Summary of Contents for G 676





















































































Reviews:

No comments

Related manuals for G 676

Lavadora EMW580E3

Brand: EAS Electric Pages: 69

Brand: EAS Electric Pages: 138

Profile PDW8680N

Brand: GE Pages: 48

Monogram ZBD5600

Brand: GE Pages: 24

Triton XL GSD6900 Series

Brand: GE Pages: 2

Brand: GE Pages: 16

Brand: GE Pages: 2

Brand: GE Pages: 20

Brand: GE Pages: 16

FDW-VRR606BDE++

Brand: FRAM Pages: 42

Brand: Heinner Pages: 86

Brand: Samsung Pages: 16

Brand: Estate Pages: 1

Brand: Bush Pages: 36

Brand: ZANKER Pages: 4

Brand: GE Pages: 72

Brand: Baumatic Pages: 40

Brand: Smeg Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands