background image

Loading the dishwasher

Note

Load the crockery so that water will
come into contact with all surfaces.
This ensures that they will be
properly cleaned.

Do not place crockery and cutlery in-
side other pieces where they may be
concealed.

Hollow items e.g. cups, glasses etc.
must be inverted in the basket.

Deep based items should be placed
at an angle such that water runs off
them freely.

Tall narrow hollow pieces should be
placed in the centre of the basket,
rather than in the corners, to ensure
good coverage of water.

Small pieces should be placed on the
cup racks.  Cups should be on the
lower rack and bowls on the top rack
so that water reaches all pieces.

The spray arms must not be blocked
by items which are too tall for the
basket or which hang through.
If necessary manually rotate the
spray arms to test.

Some foodstuffs may contain natural
dyes, e.g. carrots, tomatoes or ket-
chup.  Plastic items in the dish-
washer may discolour if large quan-
tities of these foodstuffs find their
way into the appliance on the croc-
kery.
The stability of the plastic items is
not affected by this discolouration.

Loading the dishwasher

17

Summary of Contents for G 676





















































































Reviews: