Miele G 676 Operating Instructions Manual Download Page 63 | Manualshive

Page: 63 / 84

background image

1. Fit worktop protection

A stainless steel “niro” coverplate is
supplied with the machine to protect
the underside of the worktop against
steam rising from the machine.
The coverplate is supplied as standard
with “i” models.

Squeeze sealant from the tube sup-
plied

b

into the angle of the “niro”

plate.

Align the “niro” plate

c

to the front

edge of the worktop – see illustration
- and then use tacks supplied to nail
the “niro” plate to the underside of
the worktop.

On worktops with wood or laminate
edging, the tacks should be nailed
through the holes further back from
the edge.

Installing integrated “i” Dishwashers

63

«
...
61
62
63
64
65
...
»

Summary of Contents for G 676





















































































Reviews:

No comments

Related manuals for G 676

Brand: Haier Pages: 25

Brand: Haier Pages: 41

Brand: CALOR Pages: 20

Brand: Washtech Pages: 12

Brand: Dawlance Pages: 44

Brand: Gaggenau Pages: 56

SmartWasher BenchtopPRO

Brand: CRC Pages: 4

Brand: unicraft Pages: 18

Brand: Danby Pages: 56

Brand: FAR Pages: 16

Brand: Acorn Safety Pages: 6

Porta Stream II

Brand: U-Line Pages: 9

Brand: Samsung Pages: 960

Brand: Asko Pages: 28

Brand: Frigidaire Pages: 20

Brand: Frigidaire Pages: 26

Brand: Frigidaire Pages: 28

Brand: Frigidaire Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands