Miele G 676 Operating Instructions Manual Download Page 42 | Manualshive

Page: 42 / 84

background image

Extended water inlet time

If the water pressure is less than 1.0
bar not enough water flows into the
wash cabinet. Water inlet time must be
extended.

Switch the dishwasher off with the
“On/Off” button.

Turn the programme selector to
STOP.

Hold the “Top Solo” button pressed
in and at the same time switch the
dishwasher on with the “On/Off” but-
ton.
Release the “Top Solo” button again
within two seconds.

The “On” indicator lights up and the
“Wash/Rinse” indicator flashes.

Important:
If a different indicator flashes or
lights up start the procedure from
the beginning again.
Exception:
The indicator lights “Salt” or “Rinse
aid” light up at the beginning if dish-
washing salt or rinse aid have not
been added, or need to be topped
up.

Turn the programme selector to
UNIVERSAL 65° .

If the indicator light next to the “Top
Solo” button does not light up:
Water inlet time = normal

If the indicator next to the “Top Solo”
button lights up:
Water inlet time = extended

Press the “Top Solo” button to
change the setting.

Turn the programme selector to
STOP.

Switch the dishwasher off with the
“On/Off” button.

The change to the water inlet time is
now stored in memory.

Extended water inlet time

42

«
...
40
41
42
43
44
...
»

Summary of Contents for G 676





















































































Reviews:

No comments

Related manuals for G 676

Brand: Midea Pages: 10

Brand: Samsung Pages: 36

Brand: Samsung Pages: 36

Brand: Samsung Pages: 44

Brand: Samsung Pages: 180

Brand: Samsung Pages: 180

Brand: Samsung Pages: 36

Brand: Samsung Pages: 180

Brand: Samsung Pages: 72

Brand: Hotpoint Pages: 56

Brand: Matsui Pages: 8

Brand: Zanussi Electrolux Pages: 16

Brand: CLEANVAC Pages: 8

Brand: Neue Pages: 28

1371236000 (0809)

Brand: Crosley Pages: 12

Brand: IKEA Pages: 104

Brand: Sammic Pages: 28

Brand: CaterChef Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands