Miele G 676 Operating Instructions Manual Download Page 37

Page: 37 / 84

Cleaning and care

Cleaning the spray arms

Particles of food can lodge in the spray
arm jets.
The spray arms should be inspected
and cleaned regularly (approx. every 6
months).

To do this remove the spray arms as fol-
lows.

Lift up the middle spray arm

to en-

gage the tooth-wheel mechanism.
Then unscrew the spray arm

Remove the lower basket and take
out the lower spray arm.

Dishwashers with cutlery basket:

Unscrew the upper spray arm.

Dishwashers with cutlery tray:

Pull out the cutlery tray.

Lift up the upper spray arm to en-
gage the tooth-wheel mechanism
and then unscrew the spray arm.

Using a sharp pointed object push
the food particles into the spray arm
jets and rinse well under running
water.

Please note:
After replacing the spray arms check
that they move freely.

Cleaning and care

Summary of Contents for G 676





















































































Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands

Miele G 676, Operating Instructions Manual

Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands