Miele G 676 Operating Instructions Manual Download Page 69

Page: 69 / 84

5. Fitting the (matching) door

front

The door of the kitchen base unit (with-
out the drawer facia or fittings) is nor-
mally used for the door front.

The door front is fixed to the machine
door outer panel using a fixing bracket
which has to be pre-mounted on the
rear of the door front.

Templates are provided to position the
fixing bracket and the door front accur-
ately.

Fixing brackets are already fitted on the
stainless steel door front. This front can-
not be shortened.

Door fronts differ in weight and it is
therefore essential that the door
springs are adjusted (see Step 6)
after the door front has been fitted.

On each side of the fixing bracket
position a template with the rule
markings facing outwards.

Hang the fixing bracket into the slits
in the machine door outer panel.

Push the overhanging ends of the
templates under the facia panel.

Installing integrated “i” Dishwashers

Summary of Contents for G 676





















































































Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands

Miele G 676, Operating Instructions Manual

Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands