Miele G 676 Operating Instructions Manual Download Page 72

Page: 72 / 84

6. Adjusting the door springs

The door springs are correctly adjusted
when a half opened door (approx. 45°
opening angle) remains in that position
when released.

If the door drops down, then the door
springs need to be tightened.

If, however, it rises up, then the springs
need to be released.

The adjusting screw is located in the
upper front strip at the left hand side of
the dishwasher.

Open the dishwasher door.

Adjust the door spring using a Torx
screwdriver until it is correctly bal-
anced:
– turn clockwise = tighten
– turn anti-clockwise = loosen.

7. Level and secure the

dishwasher

To ensure the stability of the dish-
washer it must be screwed to the con-
tinuous worktop after it has been posi-
tioned.

Fit the securing pieces into the slots
on both the left and right hand sides.

Push the dishwasher into the recess.

Open the dishwasher door.

The hole in the securing piece must
line up with the oval hole in the niro
steel plate.

Installing integrated “i” Dishwashers

Summary of Contents for G 676





















































































Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands

Miele G 676, Operating Instructions Manual

Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands