Miele G 676 Operating Instructions Manual Download Page 62

Page: 62 / 84

Installing integrated “i” Dishwashers

The “i” model dishwashers are spe-
cially designed for building under a
continuous worktop.

The front can be fitted with a base unit
front to match the kitchen furniture.

By using a decor set GDU “i” model
dishwashers can be converted into a
built-under “U” model dishwasher.
The decor set is supplied with a separ-
ate installation instruction leaflet.

Dishwasher G 6XX

(see data plate for model number)

Dimensions:

1) with 870 mm machine height

2) with 820 mm machine height

Range of adjustment approx. 5 cm (82-
87 cm total height).

Extended machine feet are available at
extra cost, (special accessory). These
can be used for a machine height of 87
to 92 cm.

To ensure stability, these dish-
washers must only be installed
under a continuous worktop which
must be securely screwed to neigh-
bouring units.

Dishwasher G 8XX

(see data plate for model number)

Dimensions:

1) with 890 mm machine height

2) with 840 mm machine height

Range of adjustment approx. 5 cm (84-
89 cm total height).

Extended machine feet are available at
extra cost, (special accessory). These
can be used for a machine height of 89
to 94 cm.

Installing integrated “i” Dishwashers

Summary of Contents for G 676





















































































Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands

Miele G 676, Operating Instructions Manual

Search results

Summary of Contents for G 676

Reviews:

Related manuals for G 676

Brands by name

Popular brands