micro-trak DUAL CONTROL MT-3405D Reference Manual Download Page 44

Page: 44 / 84

Plumbing Troubleshooting Chart

SYMPTOM

POSSIBLE CAUSE

POSSIBLE SOLUTION

Loses pressure in

MANUAL

• Pump Air-lock

• Clean strainer

• Larger hoses

Little or no pressure

adjustment in MANUAL

• Too much restriction in servo loop

•

Larger hoses and fittings

• No sharp bends

Pressure won’t go high

enough in MANUAL

• Pump starved or too small

• Too much agitation

• Throttle, range adjust or pressure relief valves

• Larger hoses

• Reduce agitation

• Adjust

Pressure, Speed and

Spray Rate don’t check

out according to charts

• Inaccurate pressure reading

• Dirty or worn tips

•

Use a different gauge and check

each boom.

• Clean or place

Pressure always goes

too high in AUTO

•

Minimum flow rate too high

• Inline/Bypass setting

• Re-calibrate

• Set appropriately

Pressure fluctuates

greatly in AUTO

• Sagging or kinked hoses

• Throttle valve too far closed

• Pump starved or too small

• Valve response speed set too high (“Special” Cal)

• Support or replace hoses

• Adjust throttle and range valves

• Larger hoses

• Larger pump

• Clean strainer

• Reduce valve speed setting

Summary of Contents for DUAL CONTROL MT-3405D





















































































Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands

micro-trak DUAL CONTROL MT-3405D, Reference Manual

Search results

Summary of Contents for DUAL CONTROL MT-3405D

Reviews:

Related manuals for DUAL CONTROL MT-3405D

Brands by name

Popular brands